# ++ FBCfg v1 # Configuration File, Original Name = 1.3_2.txt # created Mon Dec 3 01:26:36 UTC 2012 ## file /etc/sysconfig/gpssd.config 0 OFF-serial 115200:N:N 0 ppp 1 0 1 serial 115200:N:N 0 ppp 10 0 2 OFF-serial 115200:N:N 0 ppp 1 0 3 serial 19200:N:N 0 met 10 0 0 5017 OFF-tcp 0 0 rt17 10 7 5018 OFF-tcp 0 0 trimcom 10 0 ## end of file /etc/sysconfig/gpssd.config ## file /etc/sysconfig/met.conf 30 0R0 ## end of file /etc/sysconfig/met.conf ## file /etc/sysconfig/advertise ## end of file /etc/sysconfig/advertise ## file /etc/sysconfig/dialout ## end of file /etc/sysconfig/dialout ## file /etc/sysconfig/mgetty+sendfax/mgetty.config # # mgetty configuration file # # this is a sample configuration file, see mgetty.info for details # # comment lines start with a "#", empty lines are ignored # ----- global section ----- # # In this section, you put the global defaults, per-port stuff is below # set the global debug level to "4" (default from policy.h) debug 0 # set the local fax station id fax-id 49 115 xxxxxxxx # access the modem(s) with 38400 bps #speed 38400 # use these options to make the /dev/tty-device owned by "uucp.uucp" # and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!* #port-owner uucp #port-group uucp #port-mode 0664 # use these options to make incoming faxes owned by "root.uucp" # and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!* #fax-owner root #fax-group uucp #fax-mode 0640 # ----- port specific section ----- # # Here you can put things that are valid only for one line, not the others # # Zoom V.FX 28.8, connected to ttyS0: don't do fax, less logging # #port ttyS0 # debug 3 # data-only y # some other Rockwell modem, needs "switchbd 19200" to receive faxes # properly (otherwise it will fail with "timeout"). # #port ttyS1 # speed 38400 # switchbd 19200 # ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics # #port ttyS2 # debug 8 # init-chat "" \d\d\d+++\d\d\dAT&FS2=255 OK ATN3S0=0S13.2=1 OK # statistics-chat "" AT OK ATI2 OK # statistics-file /var/log/statistics.ttyS2 # modem-type cls2 # direct connection of a VT100 terminal which doesn't like DTR drops # #port ttyS3 # direct y # speed 19200 # toggle-dtr n # SerialPort1 port console direct y speed 115200 toggle-dtr n debug 0 # SerialPort2 port tts/1 direct y speed 19200 toggle-dtr n debug 0 # SerialPort3 port tts_max0 direct y speed 115200 toggle-dtr n debug 0 # SerialPort4 port tts_max1 direct y speed 115200 toggle-dtr n debug 0 ## end of file /etc/sysconfig/mgetty+sendfax/mgetty.config ## file /etc/sysconfig/ppp/options.console nocdtrcts 192.168.0.1:192.168.0.10 nocrtscts local ## end of file /etc/sysconfig/ppp/options.console ## file /etc/sysconfig/ppp/options.tts.1 192.168.0.2:192.168.0.1 nocrtscts local ## end of file /etc/sysconfig/ppp/options.tts.1 ## file /etc/sysconfig/ppp/options.tts_max0 192.168.0.1:192.168.0.30 nocrtscts local ## end of file /etc/sysconfig/ppp/options.tts_max0 ## file /etc/sysconfig/ppp/options.tts_max1 192.168.0.1:192.168.0.40 nocrtscts local ## end of file /etc/sysconfig/ppp/options.tts_max1 ## file /etc/sysconfig/ref_stn.config Lat: 39.882680927778 Lon: -84.136951094444 Height: 268.5120 RTCM_ID: 0 CMR_ID: 0 BINEX_ID: 0 StationName: CREF0001 StationDesc: Trimble NetRS AntSerial: 0 AntTextSerial: 00000000 AntDomeSerial: 0 AntType: 0 AntName: Unknown External AntHeight: 0.000 AntMethod: 0 ## end of file /etc/sysconfig/ref_stn.config ## file /etc/sysconfig/sessions #Name Enb Type Date/Time Duration DataType FileTemplate 1Hz 0 cont 0 30 T00:1:600:0:0:0 b:1:1:0 60min 1 cont 0 60 T00:30:600:0:0:0 a:1:0:0 ## end of file /etc/sysconfig/sessions ## file /etc/sysconfig/sleepmode no yes 24 10 ## end of file /etc/sysconfig/sleepmode ## file /etc/sysconfig/autoDelete Reserved 15000000 yes ## end of file /etc/sysconfig/autoDelete ## file /etc/sysconfig/stinger.cfg put meas_rate 10 put clock_steering on put pps_mode off pos put sv_masks E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E put l2_mode enigma put waas_mode off put waas_sv_masks E E E E E E E E E E E E E E E E E E E put everest off put elev_mask 7 put pdop_mask 99 ## end of file /etc/sysconfig/stinger.cfg ## file /etc/sysconfig/vsleep 11.000 ## end of file /etc/sysconfig/vsleep ## file /etc/sysconfig/autoReboot 2592000 ## end of file /etc/sysconfig/autoReboot ## file /etc/sysconfig/extRefFreq REFSOURCE=Internal ## end of file /etc/sysconfig/extRefFreq ## file /etc/sysconfig/interfaces auto lo iface lo inet loopback up route add -host 127.0.0.1 lo auto eth0 iface eth0 inet static address 192.168.1.2 network 192.168.1.0 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 up ifconfig eth0 mtu 1500 ## end of file /etc/sysconfig/interfaces ## file /etc/sysconfig/resolv.conf # # resolv.conf This file is the resolver configuration file # See resolver(5). # # Updated : Sun Aug 22 00:13:26 UTC 1999 ## end of file /etc/sysconfig/resolv.conf ## file /etc/sysconfig/ftp.conf ## end of file /etc/sysconfig/ftp.conf ## file /etc/sysconfig/iptables.conf ## end of file /etc/sysconfig/iptables.conf ## file /etc/sysconfig/httpPorts ## end of file /etc/sysconfig/httpPorts ## file /etc/sysconfig/ntp.conf # # Undisciplined Local Clock. This is a fake driver intended for backup # and when no outside source of synchronized time is available. The # default stratum is usually 3, but in this case we elect to use stratum # 0. Since the server line does not have the prefer keyword, this driver # is never used for synchronization, unless no other other # synchronization source is available. In case the local host is # controlled by some external source, such as an external oscillator or # another protocol, the prefer keyword would cause the local host to # disregard all other synchronization sources, unless the kernel # modifications are in use and declare an unsynchronized condition. # server 127.127.29.0 # Fireball stinger reference time # # Authentication delay. If you use, or plan to use someday, the # authentication facility you should make the programs in the auth_stuff # directory and figure out what this number should be on your machine. # authenticate no # directory for statistics files #statsdir /var/log/ntp/ # the final slash is required # Enable data logging #filegen loopstats file loopstats type day enable #filegen peerstats file peerstats type day enable #filegen clockstats file clockstats type day enable ## end of file /etc/sysconfig/ntp.conf ## file /etc/sysconfig/step-tickers ## end of file /etc/sysconfig/step-tickers ## file /etc/sysconfig/htaccess.fileaccess # $Id: htaccess.fileaccess,v 1.1 2002/11/01 19:50:50 tom Exp $ # $Source: /home/CVS/fireballTop/fireballFS/root/usr/local/fireball/defaults/sysconfig/htaccess.fileaccess,v $ AuthType Basic AuthUserFile /etc/sysconfig/htpasswd AuthGroupFile /etc/sysconfig/htgroups AuthName FileAccess ## end of file /etc/sysconfig/htaccess.fileaccess ## file /etc/sysconfig/htaccess.gpsadmin # $Id: htaccess.gpsadmin,v 1.1 2002/11/01 19:50:50 tom Exp $ # $Source: /home/CVS/fireballTop/fireballFS/root/usr/local/fireball/defaults/sysconfig/htaccess.gpsadmin,v $ AuthType Basic AuthUserFile /etc/sysconfig/htpasswd AuthGroupFile /etc/sysconfig/htgroups AuthName GpsAdmin ## end of file /etc/sysconfig/htaccess.gpsadmin ## file /etc/sysconfig/htaccess.sysadmin # $Id: htaccess.sysadmin,v 1.1 2002/11/01 19:50:51 tom Exp $ # $Source: /home/CVS/fireballTop/fireballFS/root/usr/local/fireball/defaults/sysconfig/htaccess.sysadmin,v $ AuthType Basic AuthUserFile /etc/sysconfig/htpasswd AuthGroupFile /etc/sysconfig/htgroups AuthName SysAdmin ## end of file /etc/sysconfig/htaccess.sysadmin ## file /etc/sysconfig/htgroups sysadmin: sysadmin gpsadmin: sysadmin fileaccess: sysadmin ## end of file /etc/sysconfig/htgroups ## file /etc/sysconfig/htpasswd sysadmin:3A2m5xLBGM2D2 ## end of file /etc/sysconfig/htpasswd ## file /etc/sysconfig/sysname NAME ## end of file /etc/sysconfig/sysname